{"id":4961,"date":"2026-11-20T07:20:27","date_gmt":"2026-11-20T07:20:27","guid":{"rendered":"https:\/\/sayiair.com\/?p=4961"},"modified":"2026-11-06T02:37:38","modified_gmt":"2026-11-06T02:37:38","slug":"buying-a-used-air-compressor-what-to-check","status":"publish","type":"post","link":"https:\/\/sayiair.com\/es\/buying-a-used-air-compressor-what-to-check\/","title":{"rendered":"What to Check Before Buying a Used Air Compressor"},"content":{"rendered":"<p>The advert said 6,000 hours, one owner, recently serviced. The machine was sitting in a builder&#8217;s yard under a sheet of corrugated plastic, repainted base, new gauge on the receiver, and it looked better than most used compressors we get called out to see. The seller had a folder with it and he was keen to show us the folder first.<\/p>\n<p>We asked for an oil sample before anything else, which is the point at which most of these viewings either get easy or get short. He hesitated, then found a bottle. Warm oil came out black, thin, and with a shimmer in it that you could see under a torch against the light. That shimmer is bearing material, and it ended the conversation about condition before we&#8217;d opened a single panel.<\/p>\n<h2>The counter is the last thing to trust<\/h2>\n<p>Hours are the easiest number on a compressor to change and the first number every seller quotes. We&#8217;ve seen a counter reset lower than the figure in the last service record, and we&#8217;ve seen a machine advertised with the hours off a different unit in the same yard. None of that is unusual enough to be shocking any more.<\/p>\n<p>Which means the inspection isn&#8217;t really about the counter. It&#8217;s about whether the story holds up against the metal, and the metal is honest if you know where to look. An hour with a torch and a clamp meter will tell you more than a decade of invoices, and the invoices are worth reading anyway.<\/p>\n<h2>What the oil said, and what it usually says<\/h2>\n<p>Black and thin with metal in it is the worst combination. Black on its own means it&#8217;s been hot or it&#8217;s been in there too long; thin means it&#8217;s lost viscosity, so the bearings have been running on something closer to solvent than lubricant. Metal in suspension means the damage has already started, and on a screw that damage lives in the rotor bearings, which is the most expensive place it can be.<\/p>\n<p>Milky oil tells a different story. Water in the oil points at a cooler, a drain trap that stopped working, or a <a href=\"\/es\/refrigerated-vs-desiccant-air-dryer\/\">dryer that&#8217;s been bypassed<\/a> since the last maintenance contract lapsed. That one&#8217;s fixable, but you want to know why the water got in before you assume a new filter solves it.<\/p>\n<p>The sample we send off to a lab costs less than a service call and comes back with iron, copper, silicon and water as numbers. On a machine costing five figures, skipping that test is a strange way to save forty pounds.<\/p>\n<figure class=\"wp-block-image size-large\"><img fetchpriority=\"high\" decoding=\"async\" width=\"1024\" height=\"1024\" src=\"https:\/\/sayiair.com\/wp-content\/uploads\/2026\/09\/sayi-v2155t-cast-iron-pump-22kw-motor-double-stage-0.jpg\" alt=\"SAYI V2155T 22KW double stage piston air compressor\" class=\"wp-image-4833\" title=\"\" srcset=\"https:\/\/sayiair.com\/wp-content\/uploads\/2026\/09\/sayi-v2155t-cast-iron-pump-22kw-motor-double-stage-0.jpg 1024w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/09\/sayi-v2155t-cast-iron-pump-22kw-motor-double-stage-0-300x300.jpg 300w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/09\/sayi-v2155t-cast-iron-pump-22kw-motor-double-stage-0-150x150.jpg 150w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/09\/sayi-v2155t-cast-iron-pump-22kw-motor-double-stage-0-768x768.jpg 768w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/09\/sayi-v2155t-cast-iron-pump-22kw-motor-double-stage-0-12x12.jpg 12w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/09\/sayi-v2155t-cast-iron-pump-22kw-motor-double-stage-0-500x500.jpg 500w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/09\/sayi-v2155t-cast-iron-pump-22kw-motor-double-stage-0-600x600.jpg 600w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/09\/sayi-v2155t-cast-iron-pump-22kw-motor-double-stage-0-100x100.jpg 100w\" sizes=\"(max-width: 1024px) 100vw, 1024px\" \/><figcaption>A repainted base and a new gauge tell you nothing about what the oil sample will show<\/figcaption><\/figure>\n<h2>Turning the airend by hand<\/h2>\n<p>With the machine isolated and the belt off, the airend should turn with one hand and feel like nothing much is happening. Smooth all the way round, no tight spot, no notch, no grinding at one point in the rotation.<\/p>\n<p>On this one there was a click about two thirds of the way round, which the seller explained as normal. It isn&#8217;t. A click means a bearing race has a pit in it, and a pit grows. We also pushed the shaft in and out, because end play is the other thing that ends a deal: if you can feel movement, the bearings are gone far enough that a rotor set is somewhere in the near future.<\/p>\n<p>The rotors themselves we looked at through the inlet. Scoring on the lobe faces is normal on a high-hour machine and it&#8217;s a price argument, not a reason to walk. Bright gouges are different, because something went through that shouldn&#8217;t have, and whatever it was may still be in there.<\/p>\n<figure class=\"wp-block-image size-large\"><img decoding=\"async\" width=\"1280\" height=\"1280\" src=\"https:\/\/sayiair.com\/wp-content\/uploads\/2026\/06\/Air-Dryer.webp\" alt=\"Secador de aire\" class=\"wp-image-4804\" title=\"\" srcset=\"https:\/\/sayiair.com\/wp-content\/uploads\/2026\/06\/Air-Dryer.webp 1280w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/06\/Air-Dryer-300x300.webp 300w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/06\/Air-Dryer-1024x1024.webp 1024w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/06\/Air-Dryer-150x150.webp 150w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/06\/Air-Dryer-768x768.webp 768w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/06\/Air-Dryer-12x12.webp 12w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/06\/Air-Dryer-500x500.webp 500w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/06\/Air-Dryer-600x600.webp 600w, https:\/\/sayiair.com\/wp-content\/uploads\/2026\/06\/Air-Dryer-100x100.webp 100w\" sizes=\"(max-width: 1280px) 100vw, 1280px\" \/><figcaption>A dryer bypassed for years puts water in the oil and hides it until the first oil change<\/figcaption><\/figure>\n<h2>The motor usually knows more<\/h2>\n<p>Insulation resistance first, phase to earth, with a megohmmeter. Hundreds of megohms is a healthy winding. Under one megohm and the insulation has taken on moisture or is breaking down, and cleaning it up buys you months rather than years.<\/p>\n<p>Then we went looking for a rewind. Fresh varnish inside the terminal box, a motor repainted while the compressor beside it wasn&#8217;t, terminal bolts with chewed heads, a nameplate that doesn&#8217;t match the frame. This one had new varnish and old paint, so the motor had been apart at least once. One rewind on an older machine is acceptable. A second on the same frame means it&#8217;s been cooking for years, and the efficiency on the nameplate left with the first one.<\/p>\n<p>Spinning the shaft by hand and listening at the bearing housings is the last cheap check. A dry rasp that follows rotation is a bearing job, which is straightforward on a bench and miserable in a plant room at two in the morning.<\/p>\n<h2>The receiver is a paperwork problem<\/h2>\n<p>Buyers spend an hour on the compressor and five minutes on the receiver, which is backwards, because the receiver is the part that can stop an installation dead. A pressure vessel needs a certificate, a design code and an inspection record, and in most places it needs periodic examination by an approved body.<\/p>\n<p>This one had no plate we could read and no paperwork at all. That alone would have ended it. Even with the paperwork, we&#8217;d have checked the design pressure against what the plant intended to run, because a receiver rated for 8 bar on a system running at 10 is not something a wrench can fix. Then the shell, looking for poultice corrosion under the paint where it had sat on a damp floor, and the welds around the saddles.<\/p>\n<p>Patched receivers turn up more often than people expect. A weld over a pin hole is scrap with a certificate attached, and no amount of fresh paint changes that.<\/p>\n<h2>Coolers and controllers, in that order<\/h2>\n<p>Fins blocked with dust and lint push discharge temperature up, and discharge temperature is what cooks oil and shortens bearing life. We shone a torch through the core and couldn&#8217;t see daylight, so that machine needed a clean at minimum and possibly a new core.<\/p>\n<p>The controller was the other problem. A board from 2008 with a firmware label nobody recognised, and when we rang the manufacturer the answer was that the board was obsolete, with a retrofit kit available at a price that would have doubled the deal.<\/p>\n<p>That call is worth making before money changes hands. Photograph the board, the model number and the label, then ask the manufacturer whether it&#8217;s still available and what it costs. A retrofit priced into the deal is fine. A retrofit discovered afterwards is how a bargain turns into a project, and the spares catalogue closes long before the compressor does, which is the reason we keep a <a href=\"\/es\/product-category\/air-compressor-spare-parts\/\">parts line<\/a> open at all.<\/p>\n<h2>The arithmetic that decides it<\/h2>\n<p>The seller wanted 45 percent of new, which is in the normal band. Used screw compressors trade somewhere between 30 and 50 percent depending on hours, condition and whether anyone can still service them, and under 30 percent you&#8217;re usually buying a core.<\/p>\n<p>But the percentage isn&#8217;t the decision. The decision is the total against a new machine with a warranty. Add oil, filters, separator, belt or coupling element, a cooler clean and a controller battery. Add the rebuild the oil sample implied. Add the efficiency gap, because a fixed speed machine from 2010 burns noticeably more per cubic metre than a current one and that gap runs every hour you own it.<\/p>\n<p>Our rule of thumb is blunt. If the all-in figure lands within about 60 percent of a new machine, buy new. On this compressor the repair alone came to 70 percent, so the answer was settled before we talked about price, and the seller found another buyer a fortnight later.<\/p>\n<p>None of that makes used a bad idea. A standby unit that runs 200 hours a year and mostly needs to exist is a good used purchase. A second machine for a seasonal line is another. A small shop where capital matters more than kilowatts, and a decent piston unit at a third of the price would outlast the lease, is a third. Our <a href=\"\/es\/product-category\/screw-air-compressor\/\">screw range<\/a> isn&#8217;t the answer to any of those, and we&#8217;d rather say so than sell into a job it doesn&#8217;t suit.<\/p>\n<p>What does make used a bad idea is buying on the counter and the paint. The four things that end a deal are water or metal in the oil, an airend with end play you can feel, a receiver without a certificate, and a controller nobody can supply. Everything else, scoring, a tired cooler, motor bearings, a missing guard, is a price conversation rather than a reason to walk.<\/p>\n<p>The second question on any used machine, after condition, is whether the parts exist. A model discontinued a decade ago fails that test however good the rotors look, and no discount makes up for a machine that waits three weeks for a seal.<\/p>\n<p>If the machine you&#8217;re considering is fixed speed and the load swings hard, it&#8217;s also worth pricing a VSD against it before you commit, because on a variable load the saving can be large enough to change the whole decision. We went through that in <a href=\"\/es\/vsd-air-compressor-payback-when-it-pays-off\/\">this piece on VSD payback<\/a>, and the numbers there are the ones we&#8217;d use on our own floor.<\/p>\n<p>The machine we did buy that month came from a plant closing a line, 9,000 hours, full service history, oil like honey and a receiver with a certificate in a plastic wallet. It cost more than the one in the yard. It&#8217;s been running four years without a call-out, which is the only review that counts.<\/p>","protected":false},"excerpt":{"rendered":"<p>Never buy a used compressor on the hours counter. What to check and in what order, from the oil sample to the receiver certificate, and when new is cheaper.<\/p>","protected":false},"author":1,"featured_media":4951,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_joinchat":[],"footnotes":""},"categories":[3,32],"tags":[],"class_list":["post-4961","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-resources","category-blog"],"blocksy_meta":[],"_links":{"self":[{"href":"https:\/\/sayiair.com\/es\/wp-json\/wp\/v2\/posts\/4961","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/sayiair.com\/es\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/sayiair.com\/es\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/sayiair.com\/es\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/sayiair.com\/es\/wp-json\/wp\/v2\/comments?post=4961"}],"version-history":[{"count":1,"href":"https:\/\/sayiair.com\/es\/wp-json\/wp\/v2\/posts\/4961\/revisions"}],"predecessor-version":[{"id":4975,"href":"https:\/\/sayiair.com\/es\/wp-json\/wp\/v2\/posts\/4961\/revisions\/4975"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/sayiair.com\/es\/wp-json\/wp\/v2\/media\/4951"}],"wp:attachment":[{"href":"https:\/\/sayiair.com\/es\/wp-json\/wp\/v2\/media?parent=4961"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/sayiair.com\/es\/wp-json\/wp\/v2\/categories?post=4961"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/sayiair.com\/es\/wp-json\/wp\/v2\/tags?post=4961"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}